Note: this file lists major user-visible changes only. * Changes in Quagga [] - [zebra] "no link-detect" is no longer the default. The previous release of Quagga always explicitly writes-out the link-detect configuration state. Therefore, to retain current behavior save your config with the prior release before updating. Otherwise, review your configuration. Note, most users will generally want to have link-detect enabled, and so can just remove 'no link-detect' from their interface configuration. This release also adds a global configuration to specify the default, which can be specified in the zebra configuration as: default link-detect (on|off) This will then apply to any interface which does not have link-detect explicitly configured. * Changes in Quagga 0.99.24 User-visible changes: - [pimd] New daemon: pimd provides IPv4 PIM-SSM multicast routing. - [bgpd] New feature: "next-hop-self all" to override nexthop on iBGP route reflector setups. - [bgpd] route-maps have a new action "set ipv6 next-hop peer-address" - [bgpd] route-maps have a new action "set as-path prepend last-as" - [bgpd] Update validity checking (particularly MP-BGP / IPv6 routes) was touched up significantly. Please report possible bugs. - [ripd] New feature: RIP for IPv4 now supports equal-cost multipath (ECMP) - [zebra] Multicast RIB support has been extended. It still is IPv4 only. - [zebra] "no link-detect" is now printed in configurations since it won't be the default anymore soon. To retain current behaviour, re-save your configuration after updating to 0.99.24. Distributor-visible changes: - --enable-pimd is added to enable pimd. It is considered experimental, though unless the distribution target is embedded systems with little flash, there is no reason to not include it in packages. - --disable-ipv6 no longer exists as an option. It's 2015, your C library really needs to have IPv6 support by now. - --disable-netlink no longer exists as an option. It didn't work anyway. - --disable-solaris no longer exists as an option. It only controlled some init scripts. - --enable-isisd is now the default. - mrlg.cgi is no longer included (it was severely outdated). It can be found independently at http://mrlg.op-sec.us/ - build on Linux with the musl C library should now work * Changes in Quagga 0.99.23 Known issues: - [bgpd] setting an extcommunity in a route map on a route that already has an extcommunity attribute will cause bgpd to crash. This issue will be fixed in a followup minor release. User-visible changes: - [lib] Performance enhancements on hashes and timers. - [bgpd] New feature: iBGP TTL security. - [bgpd] New feature: relaxed bestpath criteria for multipath and improved display of multipath routes in "show ip bgp". Scripts parsing this output may need to be updated. - [bgpd] Multiprotocol peerings over IPv6 now try to find a more appropriate IPv4 nexthop by looking at the interface. - [ospf6d] A large amount of changes has been merged for ospf6d. Careful evaluation prior to deployment is recommended. - [zebra] Recursive route support has been overhauled. Scripts parsing "show ip route" output may need adaptation. - [zebra] IPv6 address management has been improved regarding tentative addresses. This is visible in that a freshly configured address will not immediately be marked as usable. - [*] a lot of bugs have been fixed, please refer to the git log * Changes in Quagga 0.99.22 - [bgpd] The semantics of default-originate route-map have changed. The route-map is now used to advertise the default route conditionally. The old behaviour which allowed to set attributes on the originated default route is no longer supported. - [bgpd] There is now a replace-as option to neighbor ... local-as ... no-prepend. For details, refer to the user documentation. - [zebra] An FPM interface has been added. This provides an alternate interface to routing information and is geared at OpenFlow & co. - [snmp] AgentX is now supported; the old smux backend is considered deprecated. ospf6d has also had OSPFV3-MIB added. - [*] several issues with configuration save/load/apply have been fixed, in particular on ospf "max-metric router-lsa administrative" and "distribute-list", bgpd "no neighbor activate", isisd "metric-style", - [*] a lot of bugs have been fixed, please refer to the git log * Changes in Quagga 0.99.21 - [bgpd] BGP multipath support has been merged - [bgpd] SAFI (Multicast topology) support has been extended to propagate the topology to zebra. - [bgpd] AS path limit functionality has been removed - [babeld] a new routing daemon implementing the BABEL ad-hoc mesh routing protocol has been merged. - [isisd] a major overhaul has been picked up. Please note that isisd is STILL NOT SUITABLE FOR PRODUCTION USE. - [*] a lot of bugs have been fixed, please refer to the git log * Changes in Quagga 0.99.10 - [bgpd] 4-byte AS support added - [bgpd] MRT format changes to version 2. Those relying on bgpd MRT table dumps may need to update their tools. - [bgpd] Added new route-map set statement: "as-path exclude" - Zebra RIB updates queue has evolved into a multi-level structure to address RIB consistency issues. * Changes in Quagga 0.99.2 - [bgpd] Work queues added to bgpd to split up update processing, particularly beneficial when a peer session goes down. AS_PATH parsing rewritten to be clearer, more robust and ready for 4-byte. - [ripd] Simple authentication is no longer the default authentication mode for ripd. The default is now no-authentication. Any setups which used simple authentication will probably need to update their configuration manually. - [ospfd] 1s dead-interval with sub-second Hellos feature added. SPF timers now specified in milliseconds, and with adaptive hold-time support. RFC3137 Stub-router support added. Default ABR type is now 'cisco'. - Solaris least privileges support added. * Changes in Quagga 0.99.1 - Zserv is now buffered via threads and non-blocking in most cases for both clients and zebra, which should improve responsiveness of daemons when they must send many messages to zebra. - 'show thread cpu' now displays both cpu+system and wall-clock time, where getrusage() is available. - Background threads added and workqueue API added, with a 'show work-queues' command. Thread scheduling improved slightly. - Zebra now has a work-queue for RIB processing. See 'show work-queues' in the zebra daemon vty. - Support for interface renaming on Linux netlink systems. - GNU Zebra bgpd merges, including BGP Graceful-restart and "match ip route-source" command. - Automatic logging of backtraces should daemons crash to assist in diagnosis. See the documentation for more information on configuring logging correctly, and set --enable-gcc-rdynamic if compiling with gcc. * Changes in Quagga 0.98.0 - Logging facilities upgraded. One can now specify a severity level for each logging destination. And a new "show logging" command gives thorough information on the current logging system configuration. - Watchquagga daemon added. This is not well tested yet. Please try monitor mode first before enabling restart features. It is important to make sure that the various timers are configured with appropriate values for your site. - BGP route-server support added. See the texinfo documentation. - OSPF API initialisation is disabled by default even if compiled in. You can enable it with -a/--apiserver command line switch. - "write-config integrated" vtysh command replaced with "service integrated-vtysh-config" command. - Router id is now handled by zebra daemon and all daemons receive changes from it. Router id can be overriden in daemons' configurations of course. To fix common router id in zebra daemon you can either install non-127 address on loopback or use "router-id x.x.x.x" command. - "secondary" keyword is removed from ip address configuration. All supported OS'es have their own vision what's secondary address and how to handle it. - Zebra no longer enables forwarding by default. If you rely on zebra to enable forwarding make sure to add ' forwarding' statements to your zebra configuration file. - All libraries are built and used shared, on platforms where libtool supports shared libraries. - Router advertisement syntax is changed. In usual cases (if you didn't do any fancy stuff) it's enough to change lines in configuration from: "ipv6 nd prefix-advertisement X:X:X:X::/X 2592000 604800 autoconfig on-link" to: "ipv6 nd prefix X:X:X:X::/X" All router advertisement options are documented in texi documentation. - --enable-nssa configure switch is removed. NSSA support is stable enough. - Daemons don't look at current directory for config file any more. * Changes in Quagga 0.96.5 - include files are installed in $(prefix)/include/quagga. Programs building against these includes should -I$(prefix)/include and e.g. #include - New option --enable-exampledir puts example files in a separate directory from $(sysconfdir), easing NetBSD pkgsrc hierarchy rules compliance. - New configure options --enable-configfile-mask and --enable-logfile-mask to set umask values for config and log values. Masks default to 0600, matching previous behavior. - Import current CVS isisd from SourceForge, then merge it with the Quagga's Framework. * Changes in Quagga 0.96.4 - Further fixes to ospfd, some relating to the PtP revert. Interface lookups should be a lot more robust now. - Fix for a remote triggerable crash in vty layer. - Improvements to ripd, and addition of split horizon support. - Improved bgpd table support, now dumps at time of day intervals rather than time from startup intervals. Much improved support for IPv6 table dumps. show commands for views improved. * Changes in Quagga 0.96.3 - revert the 'generic PtP' patch. Means Quagga will no longer work with FreeSWAN, however, on the plus side this gets rid of a lot of niggly bugs which the PtP patch introduced. * Changes in Quagga 0.96.2 - Fix crash in ospfd * Changes in Quagga 0.96.1 - Iron out problem with the privileges definitions * Changes in Quagga 0.96 - Privilege support, daemons now run with the minimal privileges needed, see the documentation for details. - NSSA ABR support in ospfd. - OSPF-API support merged in. - 6WIND patch merged in. * Changes in zebra-0.93 * Changes in bgpd ** Configuration is changed to new format. * Changes in ospfd ** Crush bugs which reported on Zebra ML is fixed. ** Opaque LSA and TE LSA support is added by KDD R&D Laboratories, Inc. * Chages in ospf6d ** Many bugs are fixed. * Changes in zebra-0.92a * Changes in bgpd ** Fix "^$" community list bug. ** Below command's Address Family specific configurations are added nexthop-self route-reflector-client route-server-client soft-reconfiguration inbound * Changes in zebra ** Treat kernel type routes as EGP routes. * Changes in zebra-0.92 ** Overall security is improved. Default umask is 0077. * Changes in ripd ** If output interface is in simple password authentication mode, substruct one from rtemax. * Changes in bgpd ** IPv4 multicast and IPv6 unicast configuration is changed to so called new config. All of AFI and SAFI specific configuration is moved to "address-family" node. When you have many IPv6 only configuration, you will see many "no neighbor X:X::X:X activate" line in your configuration to disable IPv4 unicast NLRI exchange. In that case please use "no bgp default ipv4-unicast" command to suppress the output. Until zebra-0.93, old config is still left for compatibility. Old config ========== router bgp 7675 bgp router-id 10.0.0.1 redistribute connected network 192.168.0.0/24 neighbor 10.0.0.2 remote-as 7675 ipv6 bgp network 3ffe:506::/33 ipv6 bgp network 3ffe:1800:e800::/40 ipv6 bgp aggregate-address 3ffe:506::/32 ipv6 bgp redistribute connected ipv6 bgp neighbor 3ffe:506:1000::2 remote-as 1 New config ========== router bgp 7675 bgp router-id 10.0.0.1 network 192.168.0.0/24 redistribute connected neighbor 10.0.0.2 remote-as 7675 neighbor 3ffe:506:1000::2 remote-as 1 no neighbor 3ffe:506:1000::2 activate ! address-family ipv6 network 3ffe:506::/33 network 3ffe:1800:e800::/40 aggregate-address 3ffe:506::/32 redistribute connected neighbor 3ffe:506:1000::2 activate exit-address-family * Changes in ospfd ** Internal interface treatment is changed. Now ospfd can handle multiple IP address for an interface. ** Redistribution of loopback interface's address works fine. * Changes in zebra-0.91 ** --enable-oldrib configure option is removed. ** HAVE_IF_PSEUDO part is removed. Same feature is now supported by default. * Changes in ripd ** When redistributed route is withdrawn, perform poisoned reverse. * Changes in zebra ** When interface's address is removed, kernel route pointing out to the address is removed. ** IPv6 RIB is now based upon new RIB code. ** zebra can handle same connected route to one interface. ** New command for interface address. Currently this commands are only supported on GNU/Linux with netlink interface. "ip address A.B.C.D secondary" "ip address A.B.C.D label LABEL" * Changes in bgpd ** BGP flap dampening bugs are fixed. ** BGP non-blocking TCP connection bug is fixed. ** "show ip bgp summary" shows AS path and community entry number. ** New commands have been added. "show ip bgp cidr-only" "show ip bgp ipv4 (unicast|multicast) cidr-only" "show ip bgp A.B.C.D/M longer-prefixes" "show ip bgp ipv4 (unicast|multicast) A.B.C.D/M longer-prefixes" "show ipv6 bgp X:X::X:X/M longer-prefixes" "show ipv6 mbgp X:X::X:X/M longer-prefixes" ** IPv6 IBGP nexthop change is monitored. ** Unknown transitive attribute is passed with partial flag bit on. * Changes in ospfd ** Fix bug of LSA MaxAge flood. ** Fix bug of NSSA codes. * Changes in zebra-0.90 ** From this beta release, --enable-unixdomain and --enable-newrib becomes default. So both options are removed from configure.in. To revert old behavior please specify below option. --enable-tcp-zebra # TCP/IP socket is used for protocol daemon and zebra. --enable-oldrib # Turn on old RIB implementation. Old RIB implementation will be removed in zebra-0.91. ** From this beta release --enable-multipath is supported. This option is only effective on GNU/Linux kernel with CONFIG_IP_ADVANCED_ROUTER and CONFIG_IP_ROUTE_MULTIPATH is set. --enable-multipath=ARG # ARG must be digit. When ARG is 0 unlimit multipath number. ** From this release we do not include guile files. * Changes in lib ** newlist.[ch] is merged with linklist.[ch]. ** Now Zebra works on MacOS X public beta. ** Access-list can have remark. "access-list WORD remark LINE" define remark for specified access-list. ** Key of key-chain is sorted by it's idetifier value. ** prefix-list rule is slightly changed. The rule of "len <= ge-value <= le-value" is changed to "len < ge-value <= le-value". ** According to above prefix-list rule change, add automatic conversion function of an old rule. ex.) 10.0.0.0/8 ge 8 -> 10.0.0.0/8 le 32 ** SMUX can handle SNMP trap. ** In our event library, event thread is executed before any other thread like timer, read and write event. ** Robust method for writing configuration file and recover from backing up config file. ** Display "end" at the end of configuration. ** Fix memory leak in vtysh_read(). ** Fix memroy leak about access-list and prefix-list name. * Changes in zebra ** UNIX domain socket server of zebra protocol is added. ** Fix PointoPoint interface network bug. The destination network should be installed into routing table instead of local network. ** Metric value is reflected to kernel routing table. ** "show ip route" display uptime of RIP,OSPF,BGP routes. ** New RIB implementation is added. Now we have enhanced RIB (routing information base) implementation in zebra. New RIB has many new features and fixed some bugs which exist in old RIB code. *** Static route with distance value Static route can be specified with administrative distance. The distance value 255 means it is not installed into the kernel. Default value of distance for static route is 1. ip route A.B.C.D/M A.B.C.D <1-255> ip route A.B.C.D/M IFNAME <1-255> If the least distance value's route's nexthop are unreachable, select the least distance value route which has reachable nexthop is selected. ip route 0.0.0.0/0 10.0.0.1 ip route 0.0.0.0/0 11.0.0.1 2 In this case, when 10.0.0.1 is unreachable and 11.0.0.1 is reachable. The route with nexthop 11.0.0.1 will be installed into forwarding table. zebra> show ip route S>* 0.0.0.0/0 [2/0] via 11.0.0.1 S 0.0.0.0/0 [1/0] via 10.0.0.1 inactive If the nexthop is unreachable "inactive" is displayed. You can specify any string to IFNAME. There is no need of the interface is there when you configure the route. ip route 1.1.1.1/32 ppp0 When ppp0 comes up, the route is installed properly. *** Multiple nexthop routes for one prefix Multiple nexthop routes can be specified for one prefix. Even the kernel support only one nexthop for one prefix user can configure multiple nexthop. When you configure routes like below, prefix 10.0.0.1 has three nexthop. ip route 10.0.0.1/32 10.0.0.2 ip route 10.0.0.1/32 10.0.0.3 ip route 10.0.0.1/32 eth0 If there is no route to 10.0.0.2 and 10.0.0.3. And interface eth0 is reachable, then the last route is installed into the kernel. zebra> show ip route S> 10.0.0.1/32 [1/0] via 10.0.0.2 inactive via 10.0.0.3 inactive * is directly connected, eth0 '*' means this nexthop is installed into the kernel. *** Multipath (more than one nexthop for one prefix) can be installed into the kernel. When the kernel support multipath, zebra can install multipath routes into the kernel. Before doing that please make it sure that setting --enable-multipath=ARG to configure script. ARG must be digit value. When specify 0 to ARG, there is no limitation of the number of the multipath. Currently only GNU/Linux with netlink interface is supported. ip route 10.0.0.1/32 10.0.0.2 ip route 10.0.0.1/32 10.0.0.3 ip route 10.0.0.1/32 eth0 zebra> show ip route S>* 10.0.0.1/32 [1/0] via 10.0.0.2 * via 10.0.0.3 is directly connected, eth0 *** Kernel message delete installed route. After zebra install static or dynamic route into the kernel. R>* 0.0.0.0/0 [120/3] via 10.0.0.1 If you delete this route outside zebra, old zebra does not reinstall route again. Now the route is re-processed and properly reinstall the static or dynamic route into the kernel. ** GNU/Linux netlink socket handling is improved to fix race condition between kernel message and user command responce. * Changes in bgpd ** Add show neighbor's routes command. "show ip bgp neighbors (A.B.C.D|X:X::X:X) routes" "show ip bgp ipv4 (unicast|multicast) neighbors (A.B.C.D|X:X::X:X) routes" "show ipv6 bgp neighbors (A.B.C.D|X:X::X:X) routes" "show ipv6 mbgp neighbors (A.B.C.D|X:X::X:X) routes" ** BGP passive peer support problem is fixed. ** Redistributed IGP nexthop is passed to BGP nexthop. ** On multiaccess media, if the nexthop is reachable nexthop is passed as it is. ** Remove zebra-0.88 compatibility commands. "match ip prefix-list WORD" "match ipv6 prefix-list WORD" Instead of above please use below commands. "match ip address prefix-list WORD" "match ipv6 address prefix-list WORD" ** Fix bug of holdtimer is not reset when bgp cleared. ** "show ip bgp summary" display peer establish/drop count. ** Change "match ip next-hop" argument from IP address to access-list name. ** When "bgp enforce-first-as" is enabled, check EBGP peer's update has it's AS number in the first AS number in AS sequence. ** New route-map command "set community-delete COMMUNITY-LIST" is added. Community matched the CoMMUNITY-LIST is removed from the community. ** BGP-MIB implementation is finished. ** When BGP connection comes from unconfigured IP address, close socket immediately. ** Do not compare router ID when the routes comes from EBGP peer. When originator ID is same, take shorter cluster-list route. If cluster-list is same take smaller IP address neighbor's route. ** Add "bgp bestpath as-path ignore" command. When this option is set, do not concider AS path length when route selection. ** Add "bgp bestpath compare-routerid". When this option is set, compare router ID when the routes comes from EBGP peer. ** Add "bgp deterministic-med" process. ** BGP flap dampening feature is added. ** When IBGP nexthop is changed, it is reflected to RIB. ** Change "neighbor route-refresh" command to "neighbor capability route-refresh". * Changes in ripd ** Change "match ip next-hop" argument from IP address to access-list name. ** "no ip rip (send|receive)" command accept version number argument. ** Memory leak related classfull network generation is fixed. ** When a route is in garbage collection process (invalid with metric 16) and a router receives the same route with valid metric then route was not installed into zebra rib, but only into ripd rib. Moreover , it will never get into zebra rib, because ripd wrongly assumes it's already there. * Change in ospfd ** Fix bug of refreshing default route. ** --enable-nssa turn on undergoing NSSA feature. ** Fix bug of Hello packet's option is not properly set when interface comes up. ** Reduce unconditional logging. ** Add nexthop to OSPF path only when it is not there. ** When there is no DR on network (suppose you have only one router with interface priority 0). It's router LSA does not contain the link information about this network. ** When you change a priority of interface from/to 0 ISM_NeighborChange event should be scheduled in order to elect new DR/BDR on the network. ** When we add some LSA into retransmit list we need to check whether the present old LSA in retransmit list is not more recent than the new one. ** In states Loading and Full the slave must resend its last Database Description packet in response to duplicate Database Description packets received from the master. For this reason the slave must wait RouterDeadInterval seconds before freeing the last Database Description packet. Reception of a Database Description packet from the master after this interval will generate a SeqNumberMismatch neighbor event. RFC2328 Section 10.8 ** Virtual link can not configured in stub area. ** Clear a ls_upd_queue queue of the interface when interface goes down. ** "no router ospf" unregister redistribution requests from zebra. ** New command for virtual-link configuration is added. "area A.B.C.D virtual-link A.B.C.D" "area A.B.C.D virtual-link A.B.C.D hello-interval <1-65535> retransmit-interval <3-65535> transmit-delay <1-65535> dead-interval <1-65535>" "area A.B.C.D virtual-link A.B.C.D hello-interval <1-65535> retransmit-interval <3-65535> transmit-delay <1-65535> dead-interval <1-65535> authentication-key AUTH_KEY" "area A.B.C.D virtual-link A.B.C.D authentication-key AUTH_KEY" "area A.B.C.D virtual-link A.B.C.D hello-interval <1-65535> retransmit-interval <3-65535> transmit-delay <1-65535> dead-interval <1-65535> message-digest-key <1-255> md5 KEY" "area A.B.C.D virtual-link A.B.C.D message-digest-key <1-255> md5 KEY" ** Clear cryptographic sequence number when neighbor status is changed to NSM down. ** Make Summary LSA's origination and refreshment as same as other type of LSA. ** New OSPF pakcet read method. Now maximum packet length may be 65535 bytes (maximum IP packet length). ** Checking the age of the found LSA and if the LSA is MAXAGE we should call refresh instead of originate. ** Install multipath information to zebra. ** Fix socket descriptor leak when system call failed. * Changes in ospf6d ** Whole functionality has been rewritten as new code. new command "show ipv6 ospf6 spf node", "show ipv6 ospf6 spf tree", "show ipv6 ospf6 spf table" has been added. ** Change to do not send garbage route whose nexthop is not linklocal address. ** "redistribute ospf6" was generated in "router ospf6" in config file. It is fixed. ** LSDB sync bug is fixed. ** Fix bug of using unavailable route. * Changes in vtysh ** route-map and access-list configuration is merged into one configuration. ** /usr/local/etc/Zebra.conf is integrated configuration file. "write memory" in vtysh will write whole configuration to this file. ** When -b option is specified to vtysh, vtysh read /usr/local/etc/Zebra.conf file then pass the confuguration to proper protocol daemon. So make all protocol daemon's configuration file empty then invoke all daemon. After that vtysh -b will setup saved configuration. zebrastart.sh ============= /usr/local/sbin/zebra -d /usr/local/sbin/ripd -d /usr/local/sbin/ospfd -d /usr/local/sbin/bgpd -d /usr/local/bin/vtysh -b * Changes in zebra-0.89 * Changes in lib ** distribute-list can set all interface's access-list and prefix-list configuration. * Changes in ripd ** "show ip protocols" display proper distribute-list settings and distance settings. ** When metric infinity route received withdraw the route from kernel immediately it used to be wait garbage collection. ** key-chain can be used for simple password authentication. ** RIPv2 MIB getnext interface bug is fixed. * Changes in vtysh ** --with-libpam enable PAM authentication for vtysh. ** Now vtysh read vtysh.conf. This file should be ${SYSCONFDIR}/etc/vtysh.conf for security reason. Usually it is /usr/local/etc/vtysh.conf. ** "username WORD nopassword" command is added to vtysh. * Chagees in ospfd ** NBMA interface support is added. ** OSPF area is sorted by area ID. ** New implementation of OSPF refreesh. ** OSPF-MIB read function is partly added. * Changes in bgpd ** When the peering is done by ebgp-multihop, nexthop is looked up like IBGP routes. ** "show ip mbgp" commands are changed to "show ip bgp ipv4 multicast". ** New terminal commands are added. "show ip bgp ipv4 (unicast|multicast) filter-list WORD" "show ip bgp ipv4 (unicast|multicast) community" "show ip bgp ipv4 (unicast|multicast) community-list WORD" "show ip bgp ipv4 (unicast|multicast) community-list WORD exact-match" ** MBGP soft-reconfiguration command is added. "clear ip bgp x.x.x.x ipv4 (unicast|multicast) in" "clear ip bgp x.x.x.x ipv4 (unicast|multicast) out" "clear ip bgp x.x.x.x ipv4 (unicast|multicast) soft" "clear ip bgp <1-65535> ipv4 (unicast|multicast) in" "clear ip bgp <1-65535> ipv4 (unicast|multicast) out" "clear ip bgp <1-65535> ipv4 (unicast|multicast) soft" "clear ip bgp * ipv4 (unicast|multicast) in" "clear ip bgp * ipv4 (unicast|multicast) out" "clear ip bgp * ipv4 (unicast|multicast) soft" ** MED related commands are added. "bgp deterministic-med" "bgp bestpath med confed" "bgp bestpath med missing-as-worst" ** "bgp default local-preference" command is added. ** BGP confederation peer's routes are passed to zebra like IBGP route. ** Community match command is added. "show ip bgp community " "show ip bgp community exact-match" ** EBGP multihop route treatment bug is fixed. Now nexthop is resolved by IGP routes. ** Some commands are added to show routes by filter-list and community value. "show ip bgp ipv4 (unicast|multicast) filter-list WORD" "show ip bgp ipv4 (unicast|multicast) community" "show ip bgp ipv4 (unicast|multicast) community-list WORD" "show ip bgp ipv4 (unicast|multicast) community-list WORD exact-match" * Changes in zebra ** zebra read interface's address information using getifaddrs() when it is available. ** Reflect IPv6 interface's address change to protocol daemons. * Changes in zebra-0.88 * Changes in lib ** "exact-match" option is added to "access-list" and "ipv6 access-list" command. If this option is specified, the prefix and prefix length is compared as exact match mode. * Changes in zebra ** New Zebra message ZEBRA_REDISTRIBUTE_DEFAULT_ADD and ZEBRA_REDISTRIBUTE_DEFAULT_DELTE are added. ** Default administrative distance value is changed. Old New ------------------------------------------ system 10 0 kernel 20 0 connected 30 0 static 40 1 rip 50 120 ripng 50 120 ospf 60 110 ospf6 49 110 bgp 70 200(iBGP) 20(eBGP) ------------------------------------------ ** Distance value can be passed from protocol daemon to zebra. ** "show ip route" shows [metric/distance] value pair. ** Zebra Protocol is changed to support multi-path route and distance value. * Changes in ospfd ** "default-information originate [always]" command is added. ** "default-metric <0-16777214>" command is added. ** "show ip ospf database" command is integrated. LS-ID and AdvRouter can be specifed. The commands are show ip ospf database TYPE LS-ID show ip ospf database TYPE LS-ID ADV-ROUTER show ip ospf database TYPE LS-ID self-originate show ip ospf database TYPE self-originate ** route-map support for `redistribute' command are added. Supported `match' statements are match interface match ip address match next-hop Supported `set' statements are set metric set metric-type ** Pass OSPF metric value to zebra daemon. * Changes in ripd ** When specified route-map does not exist, it means all deny. ** "default-metric <1-16>" command is added. ** "offset-list ACCESS-LIST-NAME <0-16>" and "offset-list ACCESS-LIST-NAME <0-16> IFNAME" commands are added. ** "redistribute ROUTE-TYPE metric <0-16>" command is added. ** "default-information originate" command is added. ** "ip split-horizon" and "no ip split-horizon" is added to interface configuration. ** "no router rip" command is added. ** "ip rip authentication mode (md5|text)" is added to interface configuration. ** "ip rip authentication key-chain KEY-CHAIN" is added to interface configuration. ** Pass RIP metric value to zebra daemon. ** Distance manipulation functions are added. * Changes in bgpd ** Fix bug of next hop treatment for MPLS-VPN route exchange. ** BGP peer MIB is updated. ** Aggregated route has origin IGP, atomic-aggregate and proper aggregator attribute. ** Suppressed route now installed into BGP table. It is only suppressed from announcement. ** BGP router-id is properly set after "no router bgp ASN" and "router bgp ASN". ** Add check for nexthop is accessible or not for IBGP routes. ** Add cehck for nexthop is on connected or not for EBGP routes. ** "dump bgp route" command is changed to "dump bgp route-mrt" for generating MRT compatible dump output. ** Soft reconfiguration inbound and outbound is supported. ** Route refresh feature is supported. * Changes in vtysh ** VTY shell is now included into the distribution. * Changes in zebra-0.87 * Changes in lib ** "show startup-config" command is added. ** "show history" command is added. ** Memory statistics command is changed. New command show memory all show memory lib show memory rip show memory ospf show memory bgp are added. ** Filters can be removed only specify it's name. New command no access-list NAME no ip community-list NAME no ip as-path access-list NAME no route-map NAME are added. ** At any node, user can view/save user configuration. write terminal write file wirte memory are added to every node in default. ** LCD completion is added. For example both "ip" and "ipv6" command are exist, "i" then press TAB will be expanded to "ip". * Changes in bgpd ** "show ip bgp" family shows total number of prefixes. ** "no bgp default ipv4-unicast" command is added. ** Extended Communities support is added. ** "no neighbor PEER send-community extended" command is added. ** MPLS-VPN PE-RR support is added. New address family vpnv4 unicast is introduced. ! address-family vpnv4 unicast neighobr PEER activate network A.B.C.D rd RD tag TAG exit-address-family ! To make it route-reflector, please configure it under normal router bgp ASN. ! router bgp 7675 no bgp default ipv4-unicast bgp router-id 10.0.0.100 bgp cluster-id 10.0.0.100 neighbor 10.0.0.1 remote-as 65535 neighbor 10.0.0.1 route-reflector-client neighbor 10.0.0.2 remote-as 65535 neighbor 10.0.0.2 route-reflector-client neighbor 10.0.0.3 remote-as 65535 neighbor 10.0.0.3 route-reflector-client ! address-family vpnv4 unicast neighbor 10.0.0.1 activate neighbor 10.0.0.2 activate neighbor 10.0.0.3 activate exit-address-family ! * Changes in ospfd ** Many many bugs are fixed. * Changes in ripd ** Better interface up/down event handle. * Changes in zebra ** Better interface up/down event handle. * Changes in zebra-0.86 * Changes in lib ** Fix bug of exec-timeout command which may cause crush. ** Multiple same policy for "access-list", "ip prefix-list, "as-path access-list", "ip community-list" is not duplicated. ** It used to be "ip prefix-list A.B.C.D/M" match routes which mask >= M. Now default behavior is exact match so it only match routes which mask == M. * Changes in bgpd ** "match ip address prefix-list" is added to route-map. ** A route without local preference is evaluated as 100 local preference. ** Select smaller router-id route when other values are same. ** Compare MED only both routes comes from same neighboring AS. ** "bgp always-compare-med" command is added. ** Now MED value is passed to IBGP peer. ** When neighbor's filter is configured with non-existent access-list, as-path access-list, ip prefix-list, route-map. The behavior is changed from all permit to all deny. * Changes in ospfd ** Fix bug of external route tag byte order. ** OSPF Neighbor deletion bug which cause crush is fixed. ** Some route calculation bug are fixed. ** Add sanity check with router routing table. ** Fix bug of memory leak about linklist. ** Fix bug of 1-WayReceived in NSM. ** Take care of BIGENDIAN architecture. ** Fix bug of NSM state flapping between ExStart and Exchange. ** Fix bug of Network-LSA originated in stub network. ** Fix bug of MS flag unset. ** Add to schedule router_lsa origination when the interface cost changes. ** Increment LS age by configured interface transmit_delay. ** distribute-list is reimplemented. ** Fix bug of refresh never occurs. ** Fix bug of summary-LSAs reorigination. Correctly copy OSPF_LSA_APPROVED flag to new LSA. when summary-LSA is reoriginatd. ** Fix bug of re-origination when a neighbor disappears. ** Fix bug of segmentation fault with DD retransmission. ** Fix network-LSA re-origination problem. ** Fix problem of remaining withdrawn routes on zebra. * Changes in ripd ** Do not leave from multicast group when interface goes down bug is fixed. * Changes in zebra ** Remove client structure when client dies. ** Take care static route when interface goes up/down. * Changes in zebra-0.85 * Changes in bgpd ** "transparent-nexthop" and "transparenet-as" commands are added. ** Route reflector's originator-id bug is fixed. * Changes in ospfd ** Fix bug of OSPF LSA memory leak. ** Fix bug of OSPF external route memory leak. ** AS-external-LSA origination bug was fixed. ** LS request treatment is completely rewritten. Now performance is drastically improved. * Changes in ripd ** RIPv1 update is done by class-full manner. * Changes in zebra-0.84b * Changes in lib ** Fix bug of inet_pton return value handling * Changes in bgpd ** Fix bug of BGP-4+ link-local address nexthop check for IBGP peer. ** Don't allocate whole buffer for displaying "show ip bgp". Now it consume only one screen size memory. * Changes in ripd ** Fix debug output string. ** Add RIP peer handling. RIP peer are shown by "show ip protocols". * Changes in zebra-0.84a * Changes in bgpd ** Fix serious bug of BGP-4+ peering under IPv6 link-local address. Due to the bug BGP-4+ peering may not be established. * Changes in zebra-0.84 * Changes in lib ** IPv6 address and prefix parser is added to VTY by Toshiaki Takada . DEFUN string is "X:X::X:X" for IPv6 address, "X:X::X:X/M" for IPv6 prefix. You can use it like this. DEFUN (func, cmd, "neighbor (A.B.C.D|X:X::X:X) remote-as <1-65535>") ** VTY configuration is locked during configuration. This is for avoiding unconditional crush from two terminals modify the configuration at the same time. "who" command shows which termnal lock the configuration. VTY which has '*' character at the head of line is locking the configuration. ** Old logging functions are removed. Functions like log_open,log_close,openlog are deleted. Instead of that please use zlog_* functions. zvlog_* used in ospf6d are deleted also. ** "terminal monitor" command is added. "no terminal monitor" is for disabling. This command simply display logging information to the VTY. ** dropline.[ch] files are deleted. * Changes in bgpd ** BGP neighbor configuration are sorted by it's IP address. ** BGP peer configuration and actual peer is separated. This is preparation for Route Server support. ** "no neighbor PEER" command is added. You can delete neighbor without specifying AS number. ** "no neighbor ebgp-multihop" command is added. ** "no neighbor port PORT" command is added. ** To conform RFC1771, "neighbor PEER send-community" is default behavior. If you want to disable sending community attribute, please specify "no neighbor PEER send-community" to the peer. ** "neighbor maximum-prefix NUMBER" command is added. ** Multi-protocol extention NLRI is proceeded only when the peer is configured proper Address Family and Subsequent Address Family. If not, those NLRI are simply ignored. ** Aggregate-address support is improved. Currently below commands works. "aggregate-address" "aggregate-address summary-only" "no aggregate-address" "no aggregate-address summary-only" "ipv6 bgp aggregate-address" "ipv6 bgp aggregate-address summary-only" "no ipv6 bgp aggregate-address" "no ipv6 bgp aggregate-address summary-only" ** redistribute route-map bug is fixed. ** MBGP support becomes default. "configure" option --enable-mbgp is removed. ** New command "neighbor PEER timers connect <1-65535>" is added. ** New command "neighbor PEER override-capability" is added. ** New command "show ip bgp neighbor A.B.C.D advertised-route" is added. ** New command "show ip bgp neighbor A.B.C.D routes" is added. To use this command, you have to configure neighbor with "neighbor A.B.C.D soft-reconfiguration inbound" beforehand. * Changes in zebra-0.83 * bgpd ** Serious bug fix about fetching global and link-local address at the same time. Due to this bug, corrupted IPv6 prefix is generated. If you uses bgpd for BGP-4+ please update to this version. The bug is introduced in zebra-0.82. ** When bgpd send Notify message, don't use thread manager. It is now send to neighbor immediately. * Changes in zebra-0.82 ** Solaris 2.6 support is added by Michael Handler . ** MBGP support is added by Robert Olsson . Please specify --enable-mbgp to configure script. This option will be removed in the future and MBGP support will be default. * Changes in zebra ** When interface goes down, withdraw connected routes from routing table. When interface goes up, restore the routes to the routing table. ** `show interface' show interface's statistics on Linux and BSD with routing socket. ** Now zebra can get MTU value on BSDI/OS. * Changes in bgpd ** Add capability option support based upon draft-ietf-idr-bgp4-cap-neg-04.txt. ** Add `show ipv6 bgp prefix-list' command. ** Check self AS appeared in received routes. ** redistribute route-map support is added. ** BGP packet dump feature compatible with MRT. * Changes in ripd ** Fix bug of `timers basic' command's argument format. * Changes in ripngd ** Calculate max RTE using interface's MTU value. * Changes in ospfd ** Some correction to LSU processing. ** Add check for lsa->refresh_list. * Changes in ospf6d ** Many debug feature is added. * Changes in zebra-0.81 ** SNMP support is disabled in default.--enable-snmp option is added to configure script. * Changes in bgpd ** Fix FSM bug which introduced in zebra-0.80. * Changes in zebra-0.80 * access-list New access-list name space `ipv6 access-list' is added. At the same time, `access-list' statemant only accepts IPv4 prefix. Please be careful if you use IPv6 filtering. You will need to change your configuration. For IPv6 filtering please use `ipv6 access-list'. As of zebra-0.7x, user can use `access-list' for both IPv4 and IPv6 filtering. ! zebra-0.7x access-list DML-net permit 203.181.89.0/24 access-list DML-net permit 3ffe:506::0/32 access-list DML-net deny any ! Above configuration is not valid for zebra-08x. Please add `ipv6' before 'access-list' when you configure IPv6 filtering. ! zebra-0.8x access-list DML-net permit 203.181.89.0/24 access-list DML-net deny any ! ipv6 access-list DML-net permit 3ffe:506::0/32 ipv6 access-list DML-net deny any ! * prefix-list And also new prefix-list name space `ipv6 prefix-list' is added. It is the same as the change of `access-list'. `ip prefix-list' now only accept IPv4 prefix. It was source of confusion that `ip prefix-list' can be used both IPv4 and IPv6 filtering. Now name space is separated to clear the meaning of the filter. If you use `ip prefix-list' for IPv6 filtering, please change the stetement. ! zebra-0.7x ip prefix-list 6bone-filter seq 5 permit 3ffe::/17 le 24 ge 24 ip prefix-list 6bone-filter seq 10 permit 3ffe:8000::/17 le 28 ge 28 ip prefix-list 6bone-filter seq 12 deny 3ffe::/16 ip prefix-list 6bone-filter seq 15 permit 2000::/3 le 16 ge 16 ip prefix-list 6bone-filter seq 20 permit 2001::/16 le 35 ge 35 ip prefix-list 6bone-filter seq 30 deny any ! Now user can explicitly configure it as IPv6 prefix-list. ! zebra-0.8x ipv6 prefix-list 6bone-filter seq 5 permit 3ffe::/17 le 24 ge 24 ipv6 prefix-list 6bone-filter seq 10 permit 3ffe:8000::/17 le 28 ge 28 ipv6 prefix-list 6bone-filter seq 12 deny 3ffe::/16 ipv6 prefix-list 6bone-filter seq 15 permit 2000::/3 le 16 ge 16 ipv6 prefix-list 6bone-filter seq 20 permit 2001::/16 le 35 ge 35 ipv6 prefix-list 6bone-filter seq 30 deny any ! * RIP configuration If you want to filter only default route (0.0.0.0/0) and permit other routes, it was hard to do that. Now `ip prefix-list' can be used for RIP route filtering. New statement: `distribute-list prefix PLIST_NAME (in|out) IFNAME' is added to ripd. So you can configure on eth0 interface accept all routes other than default routes. ! router rip distribute-list prefix filter-default in eth0 ! ip prefix-list filter-default deny 0.0.0.0/0 le 0 ip prefix-list filter-default permit any ! * RIPng configuration Same change is done for ripngd. You can use `ipv6 prefix-list' for filtering. ! router ripng distribute-list prefix filter-default in eth0 ! ipv6 prefix-list filter-default deny ::/0 le 0 ipv6 prefix-list filter-default permit any ! * BGP configuration So far, Multiprotocol Extensions for BGP-4 (RFC2283) configuration is done with traditional IPv4 peering statement like blow. ! router bgp 7675 neighbor 3ffe:506::1 remote-as 2500 neighbor 3ffe:506::1 prefix-list 6bone-filter out ! For separating configuration IPv4 and IPv6, and for retaining Cisco configuration compatibility, now IPv6 configuration is done by IPv6 specific statement. IPv6 BGP configuration is done by statement which start from `ipv6 bgp'. ! router bgp 7675 ! ipv6 bgp neighbor 3ffe:506::1 remote-as 2500 ipv6 bgp neighbor 3ffe:506::1 prefix-list 6bone-filter out ! At the same time some IPv6 specific commands are deleted from IPv4 configuration. o redistribute ripng o redistribute ospf6 o neighbor PEER version BGP_VERSION o neighbor PEER interface IFNAME Those commands are only accepted as like below. o ipv6 bgp redistribute ripng o ipv6 bgp redistribute ospf6 o ipv6 bgp neighbor PEER version BGP_VERSION o ipv6 bgp neighbor PEER interface IFNAME And below new commands are added. o ipv6 bgp network IPV6_PREFIX o ipv6 bgp redistribute static o ipv6 bgp redistribute connected o ipv6 bgp neighbor PEER remote-as <1-65535> [passive] o ipv6 bgp neighbor PEER ebgp-multihop [TTL] o ipv6 bgp neighbor PEER description DESCRIPTION o ipv6 bgp neighbor PEER shutdown o ipv6 bgp neighbor PEER route-reflector-client o ipv6 bgp neighbor PEER update-source IFNAME o ipv6 bgp neighbor PEER next-hop-self o ipv6 bgp neighbor PEER timers holdtime <0-65535> o ipv6 bgp neighbor PEER timers keepalive <0-65535> o ipv6 bgp neighbor PEER send-community o ipv6 bgp neighbor PEER weight <0-65535> o ipv6 bgp neighbor PEER default-originate o ipv6 bgp neighbor PEER filter-list FILTER_LIST_NAME (in|out) o ipv6 bgp neighbor PEER prefix-list PREFIX_LIST_NAME (in|out) o ipv6 bgp neighbor PEER distribute-list AS_LIST_NAME (in|out) o ipv6 bgp neighbor PEER route-map ROUTE_MAP_NAME (in|out) And some utility commands are introduced. o clear ipv6 bgp [PEER] o show ipv6 bgp neighbors [PEER] o show ipv6 bgp summary I hope these changes are easy to understand for current Zebra users... * To restrict connection to VTY interface. It used to be both IPv4 and IPv6 filter can be specified with one access-list. Then the access-list can be appried to VTY interface with `access-class' stetement in `line vty' node. Below is example in zebra-0.7x. ! access-list local-only permit 127.0.0.1/32 access-list local-only permit ::1/128 access-list local-only deny any ! line vty access-class local-only ! Now IPv4 and IPv6 filter have each name space. It is not possible to specify IPv4 and IPv6 filter with one access-list. For setting IPv6 access-list in `line vty', `ipv6 access-class' statement is introduced. Let me show the configuration in zebra-0.8x. ! access-list local-only permit 127.0.0.1/32 access-list local-only deny any ! ipv6 access-list local-only permit ::1/128 ipv6 access-list local-only dny any ! line vty access-class local-only ipv6 access-class local-only ! * route-map New IPv6 related route-map match commands are added. o match ipv6 address o match ipv6 next-hop Please change your configuration if you use IP match statement for IPv6 route. zebra-0.7x config ================= ! access-list all permit any ! route-map set-nexthop permit 10 match ip address all set ipv6 next-hop global 3ffe:506::1 set ipv6 next-hop local fe80::cbb5:591a ! zebra-0.8x config ================= ! ipv6 access-list all permit any ! route-map set-nexthop permit 10 match ipv6 address all set ipv6 next-hop global 3ffe:506::1 set ipv6 next-hop local fe80::cbb5:591a ! * zebra connection Protocol daemon such as ripd, bgpd, ospfd will reconnect zebra daemon when the connection fail. Those daemons try to connect zebra every 10 seconds first three trial, then the interval changed to 60 seconds. After all, if ten connections are fail, protocol daemon give up the connection to the zebra daemon. * SNMP support (is not yet finished) Zebra uses SMUX protocol (RFC1227) for making communication with SNMP agent. Currently lib/smux.c can be compiled only with ucd-snmp-4.0.1 and http://ucd-snmp.ucdavis.edu/patches/012.patch. It can not be compiled with ucd-snmp-3.6.2. After applying the patch to ucd-snmp-4.0.1, please configure it with SMUX module. % configure --with-mib-modules=smux After compile & install ucd-snmp-4.0.1, you will need to configure smuxpeer. I'm now using below configuration. /usr/local/share/snmp/snmpd.conf ================================ smuxpeer 1.3.6.1.6.3.1 test Above 1.3.6.1.6.3.1 and test is temporary configuration which is hard coded in lib/smux.c. Yes, I know it is bad, I'll change it ASAP. * HUP signal treatment From zebra-0.80, ripd will reload it's configuration file when ripd receives HUP signal. Other daemon such as bgpd, ospfd will support HUP signal treatment soon. * Changes in zebra-0.79 * Changes in zebra ** Broadcast address setting on Linux box bug is fixed. ** Protocol daemon can install connected IPv6 route into the kernel. ** Now zebra can handle blackhole route. * Changes in ripd ** Add route-map feature for RIP protocol. ** In case of RIP version 2 routing table entry has IPv4 address and netmask pair which host part bit is on, ignore the entry. * Changes in ripngd ** Change CMSG_DATA cast from (u_char *) to (int *). (u_char *) does not work for NetBSD-currnet on SparcStation 10. * Changes in ospfd ** MaxAge LSA treatment is added. ** ABR/ASBR functionality is added. ** Virtual Link funtionality is added. ** ABR behaviors IBM/Cisco/Shortcut is added. * Changes in ospf6d ** Enclosed KAME specific part with #ifdef #endif * Changes in zebra-0.78 * Changes in lib ** SNMP support is started. ** Now Zebra can work on BSD/OS 4.X. ** Now Zebra can compiled on vanilla OpenBSD 2.5 but not yet working correcltly. * Changes in zebra ** Interface index detection using ioctl() bug is fixed. ** Interface information protocol is changed. Now interface addition/deletion and interface's address addition/deletion is separated. * Changes in bgpd ** BGP hold timer bug is fixed. ** BGP keepavlie timer becomes configurable. * Changes in ripd ** When making reply to rip's REQUEST message, fill in RIP_METRIC_INFINITY with network byte order using htonl (). ** Pass host byte order address to IN_CLASSC and IN_CLASSB macro. * Changes in ospfd ** LSA flooding works. ** Fix bug of DD processing. ** Fix bug of originating router-LSA bug is fixed. ** LSA structure is changed to support LSA aging. * Changes in ospf6d ** `ip6' statement in configuration is changed to `ipv6'. * Changes in zebra-0.77 * Changes in lib ** SIGUSR1 reopen logging file. ** route-map is extended to support multi-protocol routing information. ** When compiling under GNU libc 2.1 environment don't use inet6-apps. * Changes in zebra ** Basic IPv6 router advertisement codes added. It is not yet usable. ** Fix IPv6 route addition/deletion bug is fixed. ** `show ip route A.B.C.D' works * Changes in bgpd ** When invalid unfeasible routes length comes, bgpd send notify then continue to process the packet. Now bgpd stop parsing invalid packet then return to main loop. ** BGP-4+ withdrawn routes parse bug is fixed. ** When BGP-4+ information passed to non shared network's peer, trim link-local next-hop information. ** `no redistribute ROUTE_TYPE' withdraw installed routes from BGP routing information. ** `show ipv6 route IPV6ADDR' command added. ** BGP start timer has jitter. ** Holdtimer configuration bug is fixed. Now configuration does not show unconfigured hold time value. * Changes in ripngd ** Now update timer (default 30 seconds) has +/- 50% jitter value. ** Add timers basic command. ** `network' configuration is dynamically reflected. ** `timers basic ' added. * Changes in ripd ** Reconstruct almost codes. ** `network' configuration is dynamically reflected. ** RIP timers now conforms to RFC2453. So user can configure update, timeout, garbage timer. ** `timers basic ' works. * Changes in ospfd ** Bug of originating network LSA is fixed. ** `no router ospf' core dump bug is fixed. * Changes in ospf6d ** Redistribute route works. * Changes in zebra-0.76 * Changes in lib ** configure.in Linux IPv6 detection problem is fixed. ** Include SERVICES file to the distribution ** Update zebra.texi to zebra-0.76. * Changes in zebra-0.75 * Changes in lib ** `termnal length 0' bug is fixed. * Changes in zebra ** When zebra starts up, sweep all zebra installed routes. If -k or --keep_kernel option is specified to zebra dameon. This function is not performed. * Changes in ripngd ** Aggreagte address command supported. In router ripngd, `aggregate-address IPV6PREFIX' works. * Changes in bgpd ** Input route-map's bug which cause segmentation violation is fixed. ** route-map method improved. ** BGP-4+ nexthop detection improved. ** BGP-4+ route re-selection bug is fixed. ** BGP-4+ iBGP route's nexthop calculation works. ** After connection Established `show ip bgp neighbor' display BGP TCP connection's source and destination address. ** In case of BGP-4+ `show ip bgp neighbor' display BGP-4+ global and local nexthop which used for originated route. This address will be used when `next-hop-self'. * Changes in ospfd ** Fix bug of DR election. ** Set IP precedence field with IPTOS_PREC_INTERNET_CONTROL. ** Schedule NeighborChange event if NSM status change. ** Never include a neighbor in Hello packet, when the neighbor goes down. * Changes in zebra-0.74 * Changes in lib ** Now `terminal length 0' means no line output control. ** `line LINES' command deleted. Instead of this please use `terminal length <0-512>'. ** `terminal length <0-512>' is each vty specific configuration so it can not be configured in the configuration file. If you want to configure system wide line control, please use `service terminal-length <0-512>'. This configuration affects to the all vty interface. * Changes in zebra ** Installation of IPv6 route bug is fixed. * Changes in bgpd ** Very serious bug of bgp_stop () is fixed. When multiple route to the same destination exist, bgpd try to announce the information to stopped peer. Then add orphan write thread is added. This cause many strange behavior of bgpd. ** Router-id parsing bug is fixed. ** With BGP-4+ nexthop installation was done with global address but it should be link-local address. This bug is fixed now. ** When incoming route-map prepend AS, old AS path remained. Now bgpd free old AS path. ** `neighbor PEER weight <0-65535>' command added. * Changes in ripngd ** Almost codes are rewritten to conform to RFC2080. * Changes in ospfd ** SPF calculation timer is added. Currently it is set to 30 seconds. ** SPF calculation works now. ** OSPF routing table codes are added. ** OSPF's internal routes installed into the kernel routing table. ** Now `ospfd' works as non-area, non-external route support OSPF router. ** Call of log_rotate() is removed. * Changes in ospf6d ** LSA data structure is changed. ** Call of log_rotate() is removed. * Changes in zebra-0.73 * Changes in lib ** `config terminal' is changed to `configure terminal'. ** `terminal length <0-512>' command is added. ** Variable length argument was specified by `...'. Now all strings started with character `.' is variable length argument. * Changes in zebra ** Internal route (such as iBGP, internal OSPF route) handling works correctly. ** In interface node, `ipv6 address' and `no ipv6 address' works. ** Interface's address remain after `no ip address' bug is fixed. ** Host route such as IPv4 with /32 mask and IPv6 with /128 mask didn't set RTF_GATEWAY even it has gateway. This bug if fixed now. * Changes in bgpd ** `match as-path' argument is used to be specify AS PATH value itself directly (e.g. ^$). But it is changed to specify `ip as-apth access-list' name. ** iBGP route handle works without getting error from the kernel. ** `set aggregator as AS A.B.C.D' command is added to route-map. ** `set atomic-aggregate' command is added to bgpd's routemap. ** Announcement of atomic aggregate attribute and aggregator attribute works. ** `update-source' bug is fixed. ** When a route learned from eBGP is announced to iBGP, local preference was set to zero. But now it set to DEFAULT_LOCAL_PREF(100). * Changes in ripd ** RIPv1 route filter bug is fixed. ** Some memory leak is fixed. * Changes in ospfd ** Fix bug of DR Election. ** Fix bug of adjacency forming. * Changes in ospf6d ** Clean up logging message. ** Reflect routing information to zebra daemon. * Changes in zebra-0.72 * Changes in lib ** When getsockname return IPv4 mapped IPv6 address. Convert it to IPv4 address. * Changes in bgpd ** Change route-map's next-hop related settings. set ip nexthop -> set ip next-hop set ipv6 nexthop global -> set ipv6 next-hop global set ipv6 nexthop local -> set ipv6 next-hop local ** Add `next-hop-self' command. * Changes in ospfd ** Fix bug of multiple `network area' directive crashes. * Changes in zebra-0.71 * Changes in lib ** `log syslog' command is added. ** Use getaddrinfo function to bind IPv4/IPv6 server socket. ** `no banner motd' will suppress motd output when user connect to VTY. ** Bind `quit' command to major nodes. * Changes in zebra ** Point-to-point link address handling bug is fixed. * Changes in bgpd ** AS path validity check is added. If malformed AS path is received NOTIFY Malformed AS path is send to the peer. ** Use getaddrinfo function to bind IPv4/IPv6 server socket. * Changes in ripd ** Connected network announcement bug is fixed. ** `broadcast' command is deleted. ** `network' command is added. ** `neighbor' command is added. ** `redistribute' command is added. ** `timers basic' command is added. ** `route' command is added. * Changes in ripngd ** Fix metric calculation bug. * Changes in ospfd ** Check sum bug is fixed. * Chanegs in ospf6d ** Routing table code is rewritten. * Changes in zebra-0.70 * Changes in zebra ** Critical routing information base calculation bug check is fixed. ** zebra ipv4 message is extended to support external/internal route flavor. ** Now if internal route doesn't has direct connected nexthop, then nexthop is calculated by looking up IGP routing table. * Changes in bgpd ** `neighbor PEER update-source IFNAME' command added as ALIAS to `neighbor PEER interface IFNAME'. * Changes in ospfd ** DD null pointer bug is fixed. * Changes in zebra-0.69 * Changes in zebra ** zebra redistirbution supports dynamic notification of the route change. If you add static route while running zebra, it will be reflected to other protocol daemon which set `redistribute static'. ** If static route installation is failed due to the error. The static route is not added to the configuration and zebra routing table. ** zebra sets forwarding flag to on when it starts up. ** `no ip forwarding' turn off IPv4 forwarding. ** `no ipv6 forwarding' turn off IPv6 forwarding. ** Change `show ipforward' command to `show ip forwarding'. ** Change `show ipv6forward' command to `show ipv6 forwarding'. ** `ip route A.B.C.D/M INTERFACE' works. So you can set `ip route 10.0.0.0/8 eth0'. * Changes in bgpd ** `neighbor PEER send-community' command is added. If the option is set, bgpd will send community attribute to the peer. ** When a BGP route has no-export community attribute and send-community is set to the peer, the route is not announced to the peer. * Changes in ripngd ** When ripngd terminates, delete all installed route. ** `redistribute static', `redistribute connected' works. ** Change `debug ripng event' to `debug ripng events'. ** Change `show debug ripng' to `show debugging ripng'. ** Bug of static route deletion is fixed. * Changes in ospfd ** LS request and LS update can be send and received. * Changes in zebra-0.68 * Changes in lib ** DEFUN() is extended to support (a|b|c) statement. ** Input buffer overflow bug is fixed. * Changes in bgpd ** `ip community-list' is added. ** set community and match community is added to route-map statement. ** aggregate-address A.B.C.D/M partly works. Now it works only summary-only mode. * Changes in zebra ** IPv6 network address delete bug is fixed. * Changes in ospfd ** DR election bug fixed. ** Now Database Description can be send or received. ** Neighbor State Machine goes to Full state. * Changes in ospf6d ** router zebra related bug is fixed. * Changes in zebra-0.67 * Changes in lib ** `service password-encryption' is added for encrypted password. * Changes in bgpd ** `set as-path prepend ASPATH' is added to route-map command. ** `set weight WEIGHT' is added to route-map command. ** `no set ipv6 nexthop global' and `no set ipv6 nexthop local' command is added to route-map. ** `neighbor IP_ADDR version BGP_VERSION' command's BGP_VERSION argument changed. Old New ===================== bgp4 4 bgp4+ 4+ bgp4+-draft-00 4- ===================== If you want to peer with old draft version of BGP-4+, please configure like below: router bgp ASN neighbor PEER version 4- ** Some AS path isn't correctly compared during route selection. Now it is fixed. * Changes in ospfd ** `router zebra' is default behavior. * Changes in ospf6d ** `router zebra' is default behavior. * Changes in zebra-0.66 * Changes in zebra ** When other daemon such as gated install routes into the kernel then zebra blocks. This is only occur with netlink socket. Now socket is set as NONBLOCKING and problem is fixed. Reported and fixed by Patrick Koppen * Changes in bgpd ** Now `router zebra' is not needed to insert BGP routes into the kernel. It is default behavior. If you don't want to install the BGP routes to the kernel, please configure like below: ! router zebra no redistribute bgp ! ** redistribute connected works. ** redistribute static now filter local loopback routes and link local network. * Changes in ripd ** Some network check is added. Patch is done by Carlos Alberto Barcenilla * Changes in ripngd ** Sometimes ripngd install wrong nexthop into the kernel. This bug is fixed now. ** Now `router zebra' is not needed to insert RIPng routes into the kernel. It is default behavior. If you don't want to install the BGP routes to the kernel, please configure like below: ! router zebra no redistribute ripng ! * Changes in zebra-0.65 * Changes in lib ** `C-c' changes current node to ENABLE_NODE. Previously it doesn't. ** In ENABLE_NODE, `exit' command close vty connection. ** `service advanced-vty' enable advanced vty function. If this service is specified one can directly connect to ENABLE_NODE when enable password is not set. ** `lines LINES' command is added by Stephen R. van den Berg . * Changes in zebra ** Basic Linux policy based routing table support is added by Stephen R. van den Berg . * Changes in bgpd ** route-map command is improved: `match ip next-hop': New command. `match metric': New command. `set metric': Doc fixed. `set local-preference': DEFUN added. * Changes in ripd ** Check of announced network is added. Now multicast address is filtered. Reported by Carlos Alberto Barcenilla ** Check of network 127 is added. Reported by Carlos Alberto Barcenilla * Changes in ripngd ** Aging route bug is fixed. ** `router zebra' semantics changed. ripngd automatically connect to zebra. * Changes in ospfd ** `no router ospf' works. * Changes in ospf6d ** Bug fix about network vertex. * Changes in zebra-0.64.1. This is bug fix release. * Changes in lib ** Add check of sin6_scope_id in struct sockaddr_in6. For compilation on implementation which doesn't have sin6_scope_id. Reported by Wim Biemolt . * Changes in zebra ** Fix bug of display BGP routes as "O" instead of "B". Reported by "William F. Maton" and Dave Hartzell . * Changes in bgpd ** `no network IPV6_NETWORK' statement and `no neighbor IP_ADDR timers holdtime [TIMER]' statement doesn't work. Reported by Georg Hitsch . Now both statement work. * Changes in ospfd ** Last interface is not updated by ospf_if_update(). Reported by Dave Hartzell . * Changes in ospf6d ** Byte order of ifid is changed. Due to this change, this code will not work with previous version, sorry. ** Fix `show ip route' route type mismatch. ** Fix bug of no network IPV6_NETWORK. ** Important bug fix about intra-area-prefix-lsa. * Changes in zebra-0.64. * Changes in lib ** prefix-list based filtering routine is added. Currently used in bgpd but it will be in other daemons. * Changes in bgpd ** `no router bgp' works. But network statement is not cleared. This should be fixed in next beta. ** Route reflector related statement is added. router bgp ASN bgp cluster-id a.b.c.d neighbor a.b.c.d route-reflector-client is added. ** Prefix list based filtering is added. router bgp ASN neighbor a.b.c.d prefix-list PREFIX_LIST_NAME ** Prefix list based routing display works. show ip bgp prefix-list PREFIX_LIST_NAME * Changes in ripd ** Fix route metric check bug. Reported from Mr. Carlos Alberto Barcenilla. * Changes in ospf6d ** There are many changes. If you have interested in ospf6d please visit ospf6d/README file. * Changes in zebra-0.63 first beta package. * Changes in lib ** `copy running-config stgartup-config' command is added. ** prefix length check bug is fixed. Thanks Marlos Barcenilla . * Changes in ospfd ** DR and BDR election works. ** OSPF Hello simple authentication works. * Changes in ospf6d ** Now ospf6d can be compiled on both Linux and *BSD system. * Changes in zebra-19990420 snapshot ** `make dist' at top directory works now. * Changes in lib ** VTY has now access-class to restrict remote connection. Implemented by Alex Bligh . ! line vty access-class ACCESS-LIST-NAME ! ** `show version' command added. Implemented by Carlos Alberto Barcenilla * Changes in zebra ** `ip address' command on *BSD bug is fixed. ** `no ip address' works now for IPv4 address. ** Now `write terminal' display `ip address' configuration. * Changes in bgpd ** Redistribute static works now. Please run both zebra and bgpd. bgpd.conf should be like this: ! router zebra ! router bgp ASN redisitribute static ! * Changes in guile ** configure --enable-guile turns on zebra-guile build. ** (router-bgp ASN) allocates real bgp structre. * Changes in zebra-19990416 snapshot ** Set version to 0.60 for preparation of beta release. ** New directory guile is added for linking with guile interpreter. * Changes in zebra ** On GNU/Linux Kernel 2.2.x (with netlink support), zebra detects asynchronous routing updates. *BSD support is not yet finished. * Changes in bgpd ** `show ip bgp regexp ASPATH_REGEX' uses CISCO like regular expression instead of RPSL like regular expression. I'm planing to provide RPSL like regular expression with `show ip bgp rpsl' or something. * Changes in lib ** Press '?' at variable mandatory argument, vty prints nothing. Now vty outputs description about the argument. Fixed by Alex Bligh ** buffer.c has some ugly bugs. Due to the bug, vty interface hangs when large output date exists. This bug is fixed. Reported by Alex Bligh . * Changes in ospfd ** DR and BDR information is shown by `show ip ospf interface' command. * Changes in zebra-19990408 snapshot * Changes in bgpd ** Old BGP-4+ specification (described in old draft) treatment bug is fixed. It seems that mrtd uses this format as default. So if you have problem peering with mrtd and want to use old draft format please use version statement like this. neighbor PEER_ADDRESS remote-as ASN neighbor PEER_ADDRESS version bgp4+-draft-00 ** When AS path is epmty (routes generated by bgpd), SEGV is occur when announce the routes to eBGP peer. Reported by kad@gibson.skif.net. ** ip as-path access-list command is added. ** neighbor PEER_ADDRESS filter-list AS_LIST [in|out] command is added. ** neighbor PEER_ADDRESS timers holdtimer TIMER command is added. * Changes in all daemons ** With KAME stack, terminal interface is now bind AF_INET socket instead of AF_INET6 one. * Changes in zebra-19990403 snapshot * Changes in bgpd ** When bgpd has 'router zebra', bgpd automatically select it's router ID as most highest interface's IP Address. ** When AS path is empty (in case of iBGP), it doesn't include any AS segment. This change is for announcement to gated under iBGP. * Changes in ospfd ** OSPF hello packet send/receive works. * Changes in ospf6d ** Yasuhiro Ohara's ospf6d codes is imported. It is under development and can't be compiled on any platform. * Changes in zebra-19990327 snapshot * Changes in bgpd ** When BGP-4+ connection is done by IPv6 link-local address. One have to specify interface index for the connection. So I've added interface statement to the neighbor commmand. Please specify interface name for getting interface index like below. This statement only works on GNU/Linux. I'll support BSD ASAP. router bgp 7675 neighbor fe80::200:f8ff:fe01:5fd3 remote-as 2500 neighbor fe80::200:f8ff:fe01:5fd3 interface sit3 ** For disable BGP peering `shutdown' command is added. router bgp 7675 neighbor 10.0.0.1 shutdown ** `description' command is added to neighbor statement. router bgp 7675 neighbor 10.0.0.1 description peering with Norway. ** `show ip bgp regexp AS-REGEXP' works again. show ip bgp regexp AS7675 will show routes which include AS7675. ** When a route which is made from `network' statement is send to neighbor. Set it's nexthop to self. So 10.0.0.0/8 is announced to the peer A with source address 192.168.1.1. The routes nexthop is set to 192.168.1.1. * Changes in zebra ** In zebra/rtread_sysctl.c, function rtm_read() may overrun allocated buffer when the address family is not supported and the length is big (i.e link address). Reported Achim Patzner . * Changes in ospfd ** Now ospfd receive OSPF packet. * Changes in zebra-19990319 snapshot * Changes in configuration and libraries ** User can disable IPv6 feature and/or pthread feature by configure option. To disable IPv6: configure --disable-ipv6 To disable pthread: configure --disable-pthread ** User can disable specified daemon by configure option. Don't make zebra: configure --disable-zebra Don't make bgpd: configure --disable-bgpd Don't make ripd: configure --disable-ripd Don't make ripngd: configure --disable-ripngd Don't make ospfd: configure --disable-ospfd Don't make ospf6d: configure --disable-ospf6d ** Sample configuration files are installed as 600 file flag. Suggested by Jeroen Ruigrok/Asmodai . ** syslog logging feature is added by Peter Galbavy ** Inclusion of standard header files is reworked by Peter Galbavy ** Change description from GNU/Linux 2.1.X to GNU/Linux 2.2.X ** If daemon function exists in standard C library use it. ** To generate configure script we upgrade autoconf to 2.13. To generate Makefile.in we upgrade automake to 1.4. ** doc/texinfo.tex is added to distribution. ** Update ports/pkg/DESCR description. ** Update doc/zebra.texi. ** logfile FILENAME statement deleted. Instead of that please use log file FILENAME. * Changes in zebra * Changes in bgpd ** Communication between zebra and bgpd works now. So if there is `router zebra' line in bgpd.conf, selected route is installed into kernel routing table. ** Delete all routes which inserted by bgpd when bgpd dies. If you want to retain routes even bgpd dies please specify [-r|--retain] option to bgpd. ** BGP announcement code is reworked. Now bgpd announce selected routes to other peer. ** All output bgp packet is buffered. It's written to the socket when it gets ready. ** Output route-map works now. You can specify output route-map by: neighbor IP_ADDR route-map ROUTE_MAP_NAME out ** New route-map command added. set ip nexthop IP_ADDR set ipv6 nexthop global IP_ADDR ** Fix bug about unlock of the route_node structure. ** BGP-4+ support is added. bgpd can listen and speak BGP-4+ packet specified in RFC2283. You can view IPv6 bgp table by: `show ipv6 bgp'. ** Meny packet overflow check is added. * Changes in ripd * Changes in ripngd * Changes in ospfd ** ospfd work is started by Toshiaki Takada . Now several files are included in ospfd directory. ** ospf6d codes are merged from Yasuhiro Ohara 's ospfd work. Now codes are located in ospf6d directory. Local variables: mode: outline paragraph-separate: "[ ]*$" end: